Download Now
Amrel Systems PPS Series Driver

Download this huge ebook and read the Amrel Pps Series Users User Guide Ebook If they be almost all poured, anyone can make cuttingedge eco system. The Amrel PPS offers a complete solution to power supply system requirements. All models of the programmable power supply series are able to be. PPS - Galco can perform DC POWER SUPPLY Repairs for most industrial and Reengineering is available from our Engineered Systems department.


DRIVER FOR AMREL SYSTEMS PPS SERIES

Type: Driver
Rating:
3.18
131 (3.18)
Downloads: 650
File Size: 15.25Mb
Supported systems: Windows Vista, Windows Vista 64-bit, Windows XP 64-bit, Mac OS X, Mac OS X 10.4, Mac OS X 10.5
Price: Free* [*Free Registration Required]

Download Now
Amrel Systems PPS Series Driver

Seller assumes all responsibility for this listing.

AMREL SYSTEMS PPS SERIES DRIVERS FOR WINDOWS MAC

Shipping and handling This item will ship to Ukraine, but the seller has not specified shipping options. Contact the seller- opens in a new window or tab and request a shipping method to your location.

[SOLVED] Amrel PPS Service Manual

Shipping cost cannot be calculated. Please enter a valid ZIP Code.

DRIVER FOR AMREL SYSTEMS PPS SERIES

Item location: This Amrel Systems PPS Series will be shipped through the Global Shipping Program and includes international tracking. Learn more- opens in a new window or tab Change country: I am guessing that the pick and place machine must had some difficulty properly inserting these chips. On the back of the board, there are couple of bodge wires.

  • Amrel PPS DC Power Supply eBay
  • PPS Amrel Watt 32 Volt 2 Amp DC Power Supply Used

Other than that the layout is pretty Amrel Systems PPS Series. The auxiliary power supply board is fitted on four plastic standoffs above the main board. Looking at the bottom of the board It seems that the PCB for the auxiliary power was designed by hand.

AMREL SYSTEMS PPS SERIES DRIVERS FOR WINDOWS DOWNLOAD

The C-core transformer is an absolutely thing of beauty, it is located towards the front of the unit. The reason for the placement of the transformer is mainly for weight balancing Amrel Systems PPS Series the heatsink is located towards the rear of the case. Though the transformer is much heavier than the heatsink so the case feels a bit front heavy. From the Q.

PPS Amrel Watt 32 Volt 2 Amp DC Power Supply Used

Although the date codes on the ICs and the silkscreen suggest that this power supply was make in The picture on the right shows the socket on the Amrel Systems PPS Series of the keypad board, a couple of keypad controller ICs are also visible. One thing interesting is how the wires to the front terminal posts are routed.

If you follow the red and black wires from the front terminals you will see that they end up all the way at the back side of the power supply near the output terminal blocks. One issue to this layout is Amrel Systems PPS Series because the wires are relatively long, the voltage drop across them can be quite significant. Amrel Systems PPS Series full 2A load, the measured voltage drop approaches 10 mV at the terminals.

Since the front outputs do not have the sense terminal, you will need to use the rear terminal block connections in situations where higher precision is needed. The two pictures below are the closeups the main board.

In the left picture you can see one of the 74HC14 was not seated properly before soldered, similar to the Amrel Systems PPS Series we saw earlier on the processor board. And in the picture on the right, you can see all those 4N35 optocouplers similar to what you saw on the Amrel Systems PPS Series board. In a lab-grade programmable power supply, opto-isolation is critical as you do not want the power circuitry to destroy your entire system during a malfunction.

The picture below to the left is a shot of the processor board Amrel Systems PPS Series, you can see the date Amrel Systems PPS Series on the edge of the PCB, which clearly indicates that it was manufactured in late The output voltage resolution is determined by this DAC and at steps, the minimum adjustment interval for the output is just under 10mV. In this portion of the main board, you can see three ICs with markings sanded off.

I am not entirely sure what these three chips are used for here but clearly it must be something Amrel thought was important enough to put the effort in to obfuscate.

As mentioned earlier, the front panel binding posts are connected to the outputs all the way at the back of the unit, and here you can see the black and red wire running across the board.

Other Drivers